Just a couple questions.  Start off by saying Picture Quality is spot on. Best I’ve seen on an STB. My questions are how do you record one channel and watch another? Also how do you program the remote to control the tv? The instructions state blue led. The remote always stays green.

you need a server that allows more than one connection to record one channel and watch another

to program tv you need to point the 2 remotes at each other

same goes for source and volume buttons

keep your buzz Remote control front of your tv remote control. 

then hold tv power and source on buzz remote until you see solid green light. at this point your remote is ready to to accept keys from your tv remote control.

now press tv power on your buzz remote control then quickly press tv power on your tvs remote control. led will blink three times

now press source on buzz remote control then quickly press source on your tvs remote control. led will blink three time

now press volume up on your buzz remote control then quickly press volume up on your tvs remote control. led will blink three times

now press volume down on your buzz remote control then quickly press volume down on your tvs remote control. led will blink three times.

now you  are ready to exit. 

on your buzz remote control quickly press tv power and source together and let it go. led will go off. now all buttons should be working fine.

hope this will help. 🙂

Thanks.. I got the remote figured out.. but the recording still a no go. When I change channels it stops recording.. I do have more than 1 connection.. thanks again 

Where are u saving the recordings to usb stick or internal hard drive there is an option to change the record area in the pvr settings.

9 minutes ago, Sniper said:

Thanks.. I got the remote figured out.. but the recording still a no go. When I change channels it stops recording.. I do have more than 1 connection.. thanks again 

on same server and user/pass?

2 minutes ago, Reech said:

Where are u saving the recordings to usb stick or internal hard drive there is an option to change the record area in the pvr settings.

that doesn't matter

Saving to internal hard drive. Yes same server using Mac 

16 minutes ago, Sniper said:

Saving to internal hard drive. Yes same server using Mac 

and you're positive you have more than one connection because most servers only allow one mac connection

Yes sir 100%

1 hour ago, dishuser said:

that doesn't matter

Yes it does!  Usb drive the files seem to get corrupt very easily.

the reason I ask is because I have 2 servers on mac and can only record a channel and watch another on one of them

I would contact seller and tell them your problem cause it does work if server allows it

1 minute ago, Reech said:

Yes it does!  Usb drive the files seem to get corrupt very easily.

again

it does not matter where you record to

recording a channel and watching another depends on service

1 hour ago, dishuser said:

that doesn't matter

Yes it does!  Usb drive the files seem to get corrupt very easily.

Thanks for the help.. not a big deal really.. just thought there might have been something I was missing . Would like to get it sorted just because it’s supposed to work.

5 minutes ago, Reech said:

Yes it does!  Usb drive the files seem to get corrupt very easily.

your recording problems have nothing to do with this thread

Just now, Sniper said:

Thanks for the help.. not a big deal really.. just thought there might have been something I was missing . Would like to get it sorted just because it’s supposed to work.

like I said contact the seller because in their panel they can see and set connection amount

18 hours ago, Reech said:

Yes it does!  Usb drive the files seem to get corrupt very easily.

Try formatting your USB drive. I've recorded to USB and it works fine for me. Give it a try

On 5/16/2021 at 2:53 PM, Sniper said:

Just a couple questions.  Start off by saying Picture Quality is spot on. Best I’ve seen on an STB. My questions are how do you record one channel and watch another? Also how do you program the remote to control the tv? The instructions state blue led. The remote always stays green.

The instructions to program the remote are listed on the back of the remote. 

We also have a thread for it here https://stbtalk.com/index.php?/topic/410-how-to-program-tv-power-source-key-button/

 

Its for BT 100 but same steps apply. Just repeat the steps for each button

 

As for record and watch another. Are you using MAC, XC login or M3U?

If using XC Login. When in Live TV, press menu button, go to configuration, go to Account Info. Here it will tell you how many connections you have available. You need 2+ in order to record + watch another.